Carlo Gavazzi Temperature Meters

Temperature Meters from Carlo Gavazzi and Flow Factor

Carlo Gavazzi offers a comprehensive range of digital panel meters, HMIs and digital displays (current meters, ammeters, voltmeters, frequency meters, temperature meters and temperature controllers, tachometers, and rate meters) for the OEM, Panel Builder, Instrumentation, and MRO customer. Covering most input types (current/voltage/temperature/resistance/RPM), Gavazzi digital panel meters are well suited for your display requirements.

The Carlo Gavazzi UDM40 series is a hi-tech modular panel meter developed to meet advanced application needs. The Gavazzi UDM40 series Features a 4 digit display.  The meter front is rated at IP67, NEMA12, NEMA 4X for indoor use only. Input Power outages are 90-260 AC/DC, 18-60 AC/DC and 10-28v DC. 

The Gavazzi UDM40 series accepts most signal inputs (current, voltage, temperature, tach) and offers an analogue output as well as up to 4 digital outputs (relay). Since these are modular meters, outputs can be added at any time in the field. Remote monitoring via a PLC or PC is possible by inserting an RS485 communication module into the meter. In this way many meters can be monitored without adding a lot of expensive analogue cards to your PLC.

The Carlo Gavazzi UDM40 meter also features a 3-color display allowing at a glance indication of relative operating condition (OK - Green, Caution - Yellow, or Alarm - Red). Furthermore, the UDM40 is also able to handle and correctly display non-linear signals. Temperature inputs are Thermocouple types J,K,S,T and E and RTD resistance detectors.  Relay outputs are up to 8 amps up to 240 volts single phase. The analog outputs are 0-20mA or 0-10v DC.

The UDM40 Agency approvals are CE, cCSA, UL, e cRU.

Carlo Gavazzi UDM40TRXXXR2HXX 4 DIGIT Digital Meter, 1/8 DIN, Two 8 amp Relay outputs for control, Inputs are T/C and RTD, Input Voltage 90-240 VAC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXXXR2LXX 4 DIGIT Digital Display Meter, 1/8 DIN, Two 8 amp Relay outputs for control, Inputs are T/C and RTD, Input Voltage 18-60v AC/DC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXXXR5HXX 4 DIGIT Digital Display Meter, 1/8 DIN, FOUR 5 amp Relay outputs for control, Inputs are T/C and RTD, Input Voltage 90-240 VAC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXXXR5LXX 4 DIGIT Digital Display Meter, 1/8 DIN, FOUR 5 amp Relay outputs for control, Inputs are T/C and RTD, Input Voltage 18-60v AC/DC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXSXR2HXX 4 DIGIT Display Meter with RS 485 communications, 1/8 DIN size, Two 8 amp Relay outputs for control, Inputs are T/C and RTD, Input Voltage 90-240 VAC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXSXR2LXX 4 DIGIT Digital Display Meter with RS 485 communications, 1/8 DIN size, Two 8 amp Relay outputs for control, Inputs are T/C and RTD, Input Voltage 18-60v AC/DC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXAVR2HXX 4 DIGIT Display Meter, 1/8 DIN, Two 8 amp Relay outputs and One Analog (0-20mA or 0-10vdc) for control, Inputs are T/C and RTD, Input Voltage 90-240 VAC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXAVR2LXX 4 DIGIT Digital Display Meter, 1/8 DIN, Two 8 amp Relay outputs and One Analog (0-20mA or 0-10vdc) for control, Inputs are T/C and RTD, Input Voltage 18-60v AC/DC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXAVR4HXX 4 DIGIT Digital Meter, 1/8 DIN, Two 8 amp Relay outputs and One Analog (0-20mA or 0-10vdc) for control, Inputs are RTD and T/C, Input Voltage 90-240 VAC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXAVR4LXX 4 DIGIT Digital Display Meter, 1/8 DIN, Two 8 amp Relay outputs and One Analog (0-20mA or 0-10vdc) for control, T/C and RTD inputs, Input Voltage 18-60v AC/DC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXXXR23XX 4 DIGIT Digital Display Meter, 1/8 DIN, Two 8 amp Relay outputs for control, Inputs are T/C and RTD, Input Voltage 10-28 VDC. IP67 NEMA 4x front face

Carlo Gavazzi UDM40TRXAVR43XX 4 DIGIT Digital Display Meter, 1/8 DIN, Two 8 amp Relay outputs and One Analog (0-20mA or 0-10vdc) for control, Inputs are T/C and RTD, Input Voltage 10-28 VDC. IP67 NEMA 4x face

For more information please CONTACT Flow Factor.

Chromalox Series 4040, 6040, 8040 Temperature Controllers

Chromalox Series 40 Temperature Controllers from Flow Factor

Whether you have to manage temperature, flow, valve positioning or pressure, the Chromalox 40 Series Temperature and Process Controllers provide you with a comprehensive feature list and the flexibility to meet your most demanding process and temperature needs. Application needs change over time, but that doesn't mean that you'll need to change your controller. The Chromalox 40 series modular card design provides the owner with the flexibility to alter the functionality with ease. Expansion from 1 to 3 outputs, as well as communications and remote setpoint is easily accomplished and automatically recognized by the firmware. The optional ChromaWareTM configuration software allows the owner to program multiple units efficiently and store parameter settings for later use.

For Controllers with 120/240 AC volt input control voltage Click Here.

For Controllers with 24 Volt AC/DC, 24vac or 24vdc control voltage click Here.

4040

1/4 DIN Temperature and Process Controller

• Universal Input
• Ramping Setpoint
• Adjustable Hysteresis
• Valve Motor Drive Position
• Heater Break Alarm Function
• Remote/Dual Setpoint Options
• Security Options
• Available in 1/4 DIN
• Optional Configuration Software
• UL, cUL, CE & CSA
• 3 Year Warranty
• Jumperless Configuration
• Auto Detected Hardware
• Process & Loop Alarms
• ModBus Communications
• Auto or Manual Tuning
• Heat/Cool Operation
• Up to 3 Outputs
• Optional 24 Vdc Transmitter Power Supply

Chromalox Instruments and Controls 4040-ARR000 (314528) Digital Process Temperature Control, 1/4 DIN Size (96x96), PID Control and Heater Break Alarm, 4 digit digital displays (Process and Set Point), Analog and Relay outputs for Process control and temperature control, Universal Sensor or voltage input (T/C, 0-20mA, 0-10vdc, RTD), Input Voltage 100-240 VAC

Chromalox Instruments and Controls 4040-R00000 (314704) Digital Process Temperature Control, 1/4 DIN (96x96), On/Off and PID Control and Heater Break Alarm, 4 digit digital displays (Process and Set Point), 1 Relay output for control, Universal Sensor and process input (T/C, 0-20mA, 0-10vdc, RTD), Control Input Voltage 100-240 VAC

Chromalox Instruments and Controls 4040-RRR000 (314510) Digital Temperature Control, 1/4 DIN (96x96), PID Control and Heater Break Alarm, 4 digit digital displays (Process and Set Point), 3 Relay outputs for control, Universal input (T/C, 0-20mA, 0-10vdc, RTD), Input Voltage 100-240 VAC

8040

1/8 DIN Temperature and Process Controller

• Universal Input
• Ramping Setpoint
• Adjustable Hysteresis
• Valve Motor Drive Position
• Heater Break Alarm Function
• Remote/Dual Setpoint Options
• Security Options
• Available in 1/8 DIN
• Optional Configuration Software
• UL, cUL, CE & CSA
• 3 Year Warranty
• Jumperless Configuration
• Third-party certifications: CSA, CE, cRUus
• Auto Detected Hardware
• Process & Loop Alarms
• ModBus Communications
• Auto or Manual Tuning
• Heat/Cool Operation
• Up to 3 Outputs
• Optional 24 Vdc Transmitter Power Supply

Chromalox Controls 8040-R00000 (314544) Process Digital Temperature Control, 1/8 DIN (96x48), PID Control and On/Off Control and Heater Break Alarm, 4 digit displays (Process Variable and Set Point), 1 Relay output for control, Universal input (T/C, 0-20mA, 0-10vdc, RTD), Input Control Voltage 100-240/1/60 Volts AC

6040

1/16 DIN Temperature and Process Controller

• Optional Configuration Software
• Ramping Setpoint
• Adjustable Hysteresis
• Valve Motor Drive Position
• Heater Break Alarm Function
• Remote/Dual Setpoint Options
• Security Options
• Available in 1/16 DIN
• UL, cUL, CE & CSA
• 3 Year Warranty
• Jumperless Configuration
• Auto Detected Hardware
• Process & Loop Alarms
• ModBus Communications
• Auto or Manual Tuning
• Heat/Cool Operation
• Up to 3 Outputs
• Optional 24 Vdc Transmitter Power Supply

Chromalox Process Controls 6040-RRR000 (314640) Digital Process Temperature Control, 1/16 DIN (48x48), On/Off and PID Control and Heater Break Alarm, 4 digit displays (Process and Set Point), 3 Relay outputs (2 amps) for control, Universal Sensor input (T/C, 0-20mA, 0-10vdc, RTD), Input Control Voltage 100-240 VAC

Chromalox Instruments 6040-S00000 (314720) Process Temp Control, 1/16 DIN (48x48), PID Control and Heater Break Alarm, 2 digital displays (Process and Set Point), 1 Solid State Relay output (0/10 volts dc) for control, Universal Sensor and voltage input (T/C, 0-20mA, 0-10vdc, RTD), AC Input Voltage 100-240/1/60

Chromalox Instruments and Controls 6040-SR0000 (314632) Temperature Controller, 1/16 DIN (48x48), PID Control and Heater Break Alarm, 4 digit digital displays (Process Variable and Set Point in degrees F or C), 1 RELAY Output and 1 SSR Output for control, Voltage and Sensor input (T/C, 0-20mA, 0-10vdc, RTD), Control Input Voltage 100-240 VAC

Chromalox Instruments and Controls 6040-SR0001 Digital Temperature Control, 1/16 DIN (48x48), On/Off and PID Control and Heater Break Alarm, digital displays (2) (Process and Set Point), 1 RELAY Output and 1 Solid State Relay Output Driver for control, Universal input (T/C, 0-20mA, 0-10vdc, RTD), Input Voltage 24-48v AC/DC

Chromalox 6040 PCNs also available  314624   314616   314659

For Questions or Quotes 866-360-9830 or email to info@flowfactor.com

Flow Factor Contact Us Page

Ohms Law and Wattages for Electric Heaters and Elements

Flow Factor and Ohms Law

Electric Heaters and heating elements become hot due to a voltage being pushed through a wire.  The resistance in the wire measured in Ohms creates the heat.  The more resistance the hotter the wire gets. The more voltage pushed through the wire, the hotter the wire gets. Simply the smaller the wire (or the longer the wire run) the more resistance it gives to the voltage passing through.

So as voltage increases the wattage will increase four fold.  As the voltage decreases the wattage will decrease by a factor of 4 as well.  The below table shows the percentage of drop or gain with different applied voltages to a heating element.

Rated at 480 volts the expected wattage % is

575 applied  144%

480 applied  100% (Rated Watttage)

440 applied   84%

240 applied   25%

120 applied    6%

Rated at 277 volts the expected wattage % is

277 applied 100% (rated Wattage)

240 applied  75%

230 applied  69%

208 applied  56%

120 applied  19%

Rated at 240 volts the expected wattage % is

277 applied 133%

240 applied 100% (rated wattage)

230 applied  92%

208 applied  75%

120 applied  25%  (1/4 wattage)

Rated at 120 volts the expected wattage % is

240 Applied  400%  (4 times wattage - Dangerous) 

208 Applied  300%  (3 times wattage - Dangerous)

120 Applied  100%  (rated Wattage)

110 Applied   84%

This is all based on Ohm's Law or I=E/R

Simple Ohms Law equations are:

Amps = WATTS / VOLTS

Watts = VOLTS x AMPS

Ohms = VOLTS / AMPS

Volts = AMPS x OHMS

A Conductor Wire's resistance is constant based on wire size and length.

A heater's watt rating is based on the wire used in the heating element and the voltage applied.

To get a 15 kilowatt rated heater run at 480 volts; a wire with a resistance of 15.4 Ohms is used.

(If there are three elements in the heater, then each is rated at 5 kw and the resistance of the wire would be 46.)

Knowing amps is very important for large immersion heater loads to size contractors, SCR's, Fusing and Thermostats.

Contact Flow Factor for all sizing help with heaters and accessories.

www.flowfactor.com

866-360-9830

Penberthy Jet Pumps

Penberthy jet pumps from Flow Factor

Penberthy Jet Pump (eductor)

56877-090   GL series STEEL

56877-010   GL series IRON

56877-030   GL Series STAINLESS

56875-010   GL series IRON

56876-000   GH series BRONZE

56844-000    LL series  BRONZE

56870-000   GH series  BRONZE

56849-020   LH series PVC

56847-020   LH series PVC

56873-010   GL series IRON

56877-000   GL series BRONZE  1-1/2 inch

56874-010   GH series IRON

56880-000   GH series BRONZE

56876-030   GH series  STAINLESS

56864-030  GH series in Stainless

Penberthy eductors cane used for mixing, heating and blending of gases, liquids and some solids.

216-765-4231

info@flowfactor.com

Parker Skinner Fluid Control Division

Parker's FCD ( Fluid Control Division ) manufacturers of the Skinner and Gold Ring lines of solenoid valves and the Sinclair Collins line of process control valves, now offers a six-port Marine Selector Valve for electric remote tank selection in boats with multiple diesel fuel tanks.

Being a solutions provider means helping our customers achieve higher levels of success by engineering the best systems for their requirements. It means looking at the customer applications from many angles to find new ways to create value.


Parker 2 way valves for on off control of fluids (water, oil, air, gasses). Powered by a solenoid coil.

Parker 3 way valves for operating cylinders, control valves and diverting flows.

Parker 4 way valves for operating double acting cylinders and other accuators.

Parker Angle Body valves for slurries and other hard to control fluids.  2 and 3 way available and analog control.

Parker Sinclair Collins Control valves for proportional valve control.

Please use our Solenoid Valve Parts form for quotes and questions.

Call toll free for quotes and questions.  866-360-9830

Stiebel Eltron Tempra Tankless Water Heaters

Tankless Technology by the Electric Tankless Leader, Stiebel-Eltron and Flow Factor

The Tempra^® series has been redesigned completely inside and out - upgraded heavy-duty electronics, a simple single flow sensor design, a hinged cover for easy access, and Tempra Advanced Flow Control^™ for the Tempra^® Plus.

The Tempra^® continually heats water instantaneously as you require it - and only when you require it. The Tempra^® unit completely replaces a conventional tank heater with no disruption to your comfort and hot water needs.

he Tempra^® Plus is the most technologically advanced tankless water heater available on the market today.

Tempra Advanced Flow Control^™ is exclusive to the Tempra^® Plus and ensures a constant temperature output no matter how great the hot water demand is.

Tempra Advanced Flow Control^™ technology works by automatically adjusting the flow of water to eliminate unpleasant temperature fluctuation.

What that means to you is a consistently satisfying experience every time, all the time!

Electric tank type water heaters are subject to stand-by losses which amount to 15 - 20% of the kWH used. In addition, water in a tank has to be heated hotter than necessary to account for these stand-by losses.

Changing to a tankless system like the Tempra^® eliminates these problems and results in typical savings of at least 15 - 20% on the hot water portion of your electric bill.

Set the knob on the front cover and enjoy water temperatures between 86°F (30°C) and 140°F (60°C). Change the desired temperature at anytime. Advanced microprocessor technology ensures that the water temperature never deviates from the set point.

The Tempra® has several advantages over a gas-type tankless water heater. Compared to many similar gas tankless models the Tempra® is less expensive to purchase. Installation is also much simpler and cheaper since it is not necessary to vent a Tempra® to the outside. The venting that a gas unit requires causes anywhere from a 10 - 20% efficiency reduction from heat escaping out the exhaust pipe. Furthermore, for every cubic foot of gas burned, roughly two cubic feet of air have to be mixed in to create ideal combustion. In a cold climate, this hurts efficiency further. When a gas unit fires it draws in air around it, heats the water, and then expels warm exhaust outside. Since no house is airtight, this suction action causes a drafting condition where cold air from the outside seeps back in through door cracks and other parts of the house that may not be airtight. By nature of the design, the Tempra® is nearly 100% efficient; converting 100% of the electrical energy it consumes into heat. All that heat is then transferred to the water - none is lost to the outdoors.

The Tempra^® is a tankless water heater system, and is thereby not subject to seismic code. There is no need for preventative construction, as required when using a tank type water heater.

The Tempra^® has several temperature and flow sensors which feed their readings into the unit’s proprietary microprocessor control. Heating elements are engaged in stages, achieving the temperature you desire. The Tempra^® continually monitors the water temperature it produces.

STIEBEL ELTRON Tempra 12 Plus, 240 V / 208 V, 12.0 kW, single phase

STIEBEL ELTRON Tempra 15 Plus, 240 V / 208 V, 14.4 kW, single phase

STIEBEL ELTRON Tempra 20 Plus, 240 V / 208 V, 19.2 kW, single phase

STIEBEL ELTRON Tempra 29 Plus, 240 V / 208 V, 28.8 kW, 1 or 3 phase

STIEBEL ELTRON Tempra 36 Plus, 240 V / 208 V, 36 kW, 1 or 3 phase

866-360-9838

info@flowfactor.com

Bosch / Ariston S series Mini-Tanks

Ariston Mini-Tanks updated to S series - Flow Factor

The new Ariston GL6S Plus electric mini-tank water heaters have just arrived. This water heater is the direct replacement for the recently obsoleted Ariston GL6+ (GL6PLUS).

The main difference between the older GL6+ and the new GL6+S is that the GL6+ came with a power cord that plugged directly into a 120V wall socket while the new GL6+S does not come with a power cord. The GL6+S must be hardwired at the time of installation.

Globaltowne does carry a 6' cord for the Ariston GL6+S

Here are the features of the new GL6+S: 

• 6-year warranty on tank
• Glass-lined tank for longer life
• Mounts on wall or floor
• Temperature/pressure relief valve included
• Must be hard-wired to 120V
• Dimensions: 17.5" x 17.5" x 14 1/2"
• Recovery at 90 Deg F Rise: 7 GPH
• 12.5 AMPS and 1500W Heating Capacity
• Temperature Range: 65 Deg F to 145 Deg F
• Meets ASHRAE 90.1 Standard
• Relief Valve = Installed
• Power cord not included

The new Ariston GL6+S model has many new improvements since it has been upgraded. The mini tank has a new temperature adjustment knob on the front of the unit to raise and lower the temperature from 65 Deg F to 145 Deg F. On the older model you would have to remove the blue oval cover to access the temperature knob.

The Ariston GL6+S model has a new improved thermostat that features a new sensing probe that is attached to the thermostat and inserts into the cavity of the new element so the heater can adjust temperatures quicker and maintain a more consistent heat.

Designed by the world's leading point-of-use water heater manufacturer, the New Ariston GLS series combines Italian design and state of the art features including glass-lined tanks, a 6-year warranty and highest recovery time. 

Installing an Ariston electric mini-tank water heater under the sink puts hot water right where you need it - at the point of use. Lightweight and compact and also the Ariston mini tank heaters are great for those long hot water runs from your tank heater or tankless heater and will shorten the wait time for hot water.

The New Ariston GL2.5S mini-tank electric water heater stores 2.5 gallons of hot water. 

The New Ariston GL4S mini-tank electric water heater stores 4 gallons of hot water. 


Please note: The New Ariston GL2.5S is not the direct replacement for the Ariston GL2.5 as the Ariston Gl2.5S is 10 3/4" in depth and the older Ariston GL2.5 was 10 1/4" deep.  The new Ariston GL4S is not the direct replacement for the Ariston GL4 as the GL4S is 13 1/2" in depth and the older Gl4 was 12 1/4" deep.  The replacement parts for the new Ariston GL2.5S and the GL4S will not work for the older GL2.5 and GL4 mini tank heaters.

• 6-year warranty on tank 
• Glass-lined tank for longer life  
• Mounts on wall or floor 
• Temperature/pressure relief valve included  
• Plugs into standard 120 volt outlet
• Dimensions: GL2.5S-13 3/4" x 13 3/4" x 10 3/4", GL4S-13 3/4" x 13 3/4" x 13 1/2"
• Recovery at 90 Deg F Rise: 7 GPH 
• 12.5 AMPS and 1500W Heating Capacity 
• Temperature Range: 65 Deg F to 145 Deg F  
• Meets ASHRAE 90.1 Standard
• Relief Valve = Installed

The new Ariston GL2.5S & GL4S models have many new improvements since they have been upgraded.  The mini tanks have a new temperature adjustment knob on the front of the unit to raise and lower the temperature from 65 Deg F to 145 Deg F.  On the older models you would have to remove the blue oval cover to access the temperature control knob.

The Ariston GL2.5S & GL4S models have a new improved thermostat that features a new sensing probe that is attached to the thermostat and inserts into the cavity of the new element so the heater can adjust temperatures quicker and maintain a more consistent heat.

www.flowfactor.com

866-360-9830